Search

This is RF Transmitter Receiver Module 315MHz Wireless Link Kit For Arduino.

This wireless transmitter and receiver pair operates at 315Mhz. They can easily fit into a breadboard and work well with microcontrollers to create a very simple wireleReceiving frequency (MHz)ss data link. Since these are only transmitters, they will only work communicating data one-way, you would need two pairs (of different frequencies) to act as a transmitter/receiver pair.

This Radio Transmitter & Receiver pair is perfectly matched to allow you to control items from a distance up to 500 feet wirelessly! Connect the transmitter to your Arduino, Raspberry Pi or other microcontroller and the receiver to whatever you’d like to control.

Both the transmitter and receiver are in tune to the same Radio Frequency so that when the transmitter emits a signal, the receiver will hear it wirelessly. Great for easy and simple wireless control! Arduino & Raspberry Pi 2 / B / B / A Compatible!

A voltage-raising module with a maximum capacity of 8 watts follows the input supply voltage, where the output is fixed at 12 volts. The output can be changed by changing the resistors on the module, to give an output voltage of up to 20 volts.

• The possibility of adjusting the output voltage in a wide range of 5-12 volts.
• The module contains a place for installing the USB jack.
• It is not recommended that the output voltage be ten times greater than the input voltage to avoid damage and overheating.
• Equipped with indicator light.

• On-board ADXL345, it's a low cost cap-based accelerometer sensor
• Support 5V/3.3V voltage input, onboard RT9161, better performance than 1117, faster load the appropriate speed, it is ideal for high noise power supply environment
• Common Pins were lead out, Pin distance is standard 100mil (2.54mm), compatible for your new system

Features: 

1. Come with a driver
2. Power-ON trigger work
3. 108KHz high frequency oscillator
4. Micron level aperture
5. Glazed surface of atomized sheet

Specification:

1. Product name: 108KHz 20mm USB Humidifier
   
2. Work Voltage:DC 4.5V~5.0V
   
3. Work Power:2W
   
4. Work Frequency:108KHz( /-3KHz)
   
5. Power Type:Female USB Socket
   
6. Diameter without rubber ring:16mm
   
7. Diameter with rubber ring:20mm
   
8. Spray Diameter:5um
   
9. Spray hole:740 holes
   
10. Spray speed:50ml/h
    
11. Work Temperature:0℃~85℃
    
12. Work Humidity:10%~90%RH
    
13. Driver Size:35*19*15mm

This is TDA7492p based is Class-D audio amplifier. This module has integrated a Bluetooth module, all the used components in the amplifying process, output connectors and control buttons. All you need to do is supply 12V to 36A to it, connect an 8-ohm 50W speaker to each output and connect a Bluetooth device to it and enjoy and control your favourite music wirelessly.

Product Details:

Description:

This product is an embedded module based on the universal serial interface network standard,built-in TCP / IP protocol stack, enabling the user serial port, wireless network (wifi) interface between the onversions. Through the HLK-M30 module, the traditional serial devices do not need to change any configuration, userdata can be transmitted through the Internet network. Provide a quick solution for the user's serial devices to transfer data via WiFi.

Features:

• WiFi Sta/Soft AP Mode
• Support Smart Connection
• Support transparent transmission mode
• Support multiple security authenti-cation mechanisms:
  • WEP64/WEP128/ TKIP/ AES
  • WEP/WPA-PSK/WPA2-PSK
• Support wireless roam
• Support multiple network protocols:
  • TCP/UDP/ /DHCP/DNS
• Support AT instruction Set

Applications:

• WiFi Power Switch
• Smart Home; Smart Building
• OBDII WiFi Diagnose
• RFID Data Transfer
• Toys and Gaming Peripherals
• Industrial Systems
• Telemetry
• Remote Control

Benefits:

• Low Power consumption
• Ready to use in products
• Minimizes product development
• No RF test required for systems
• Serial to WiFi; Smart; Small;
• Support Smart Connection
• Transparent Transmission
• Compliant with CE and FCC

Product Details:

The Daqpr is a portable, battery operated data acquisition and logging system offering 16-bits, high-resolution, 8 channel data logging. The DaqPRO features powerful graphical display and analysis functions for measuring voltage, current and temperature. It is designed to provide a professional.

Product Details:

We are a noteworthy organization in this domain, occupied in providing pristine quality range of Remote IO Module. Under the guidance of dexterous professionals, this IO module is designed using the supreme quality components and ultra modern technology at our vendors end. Our provided IO module is used for automation of typically industrial electromechanical processes, such as control of machinery on factory assembly lines, amusement rides, or light fixtures.
Features:

• Excellent functionality
• Easy installation
• Dimensional accuracy