Search
Search Criteria
Products meeting the search criteria
The enable pin “EN” will disable the device when HI (Vcc) and enable when LO (GND). The onboard jumper can be left open to allow external control of enable/disable of the module. There are two potentiometers on the module one controlling operating frequency (centred at 38 kHz) the other controlling intensity. The detector was designed for 38 kHz and the onboard oscillator circuit is based on a 555 timer.
The GP2Y0A02 uses a 3-pin JST PH connector that works with our 3-pin JST PH cables for Sharp distance sensors (not included); the top picture on the right shows a shorter-range Sharp analog distance sensor with one of these cables. These cables have 3-pin JST connectors on one end and are available with pre-crimped male pins, pre-crimped female pins, and with unterminated wires on the other end.
Specification:Product Type: LEDShape: Round LED 5mm DIP typeLens type: white mistStandard Forward Voltage: 2.5-6V Forward Current: 40mA
HC-SR505 Mini Infrared PIR Motion Sensor Precise Infrared Detector Module H
HC-SR505 small body sensing module is based on infrared technology, automatic control products, high sensitivity, high reliability, ultra-small, ultra-low-voltage operation mode. Widely used in various auto-sensing of electrical equipment, especially battery-powered automatic control products.
hermoelectric coolers (TEC or Peltier) create a temperature differential on each side. One side gets hot and the other side gets cool. Therefore, they can be used to either warm something up or cool something down, depending on which side is used. You can also use temperature differential to generate electricity.
A thermoelectric cooling (TEC) module is a semiconductor-based electronic component that functions as a small heat pump. By applying DC power source to a TEC, heat will be transferred from one side of the module to the other. It creates a cold and hot side. They are widely used in industrial areas, for example, computer CPU, CCDs, portable refrigerators, medical instruments, and so on.
When exposed to different temperatures on both sides it will also work as a generator and generate electricity depending on the temperature difference
Minimum Order Quantity | 10 Piece |
Brand | R S Enter |
Operating voltage | 5V |
Input Voltage | 7-12V |
Clock Speed | 16 MHZ |
Flash Memory | 32 KB |
Features:
Main changes from the older version:
- Add two rows of the holes for the pins. So it can be connected with normal Dupont line.
- Add 3 rows of the holes for wiring.
- Change the in-line package of ATMEGA328P to flat package.
- CH340G replace ATmega16U2
- We program & test all devices with LED blinking Program.
- Please make sure to connect the device to USB & test if the LED-"L" is blinking,
- This shows the device is working perfectly (Don't modify program without completing this preliminary test).
- Install CH340 USB Driver (Download: http://goo.gl/NWEz9O )
- Install Arduino IDE (Download: http://arduino.cc/en/Main/Software )
- Connect Board to Computer & Launch Arduino IDE.
- Select board as "Uno" in Arduino IDE.
- Select the COM port (You can know COM Port No. in Control Panel > Device Manager).
- Start burning your programs.
- Microcontroller: ATmega328
- Digital I/O Pins: 14 ( of which 6 provide PWM output)
- Analog Input Pins: 6
- DC Current per I/O Pin: 40mA
- DC Current for 3.3V pin: 50mA
- (ATmega328) of which 0.5KB used by bootloader
- SRAM: 2 KB (ATmega328)
- EEPROM: 1 KB ( ATmega328)
- USB Chip CH340G
- 1 X Piece Arduino UNO R3 Compatible Development Board - ATmega328P CH340.
- 1 X USB Cable
- Dupont Pins
Brand | REES52 |
Part Number | ADXL335 |
Accelerometer Type | AC Response |
Number of Axes | 3 |
Sensing Axis | XYZ |
Output Type | Analog |
Excitation Voltage | 1.8 V to 3.6 V. |
Operating Temperature Range | -20 to 70 deg C |
ADXL335 is a Breakout board based on 3 axis ADXL335 IC from Analog Devices. The Accelerometer Module require no external devices and works on 5V power supply. It can be directly interfaced to ADC of a microcontroller without any external components.
This module can be used to sense motion or tilt(in case of non moving) in 3 axis.This is the latest in a long, proven line of Analog Sensors- the holy grail of accelerometers. The ADXL335 is a triple axis MEMS accelerometer with extremely low noise and power consumption - only 320uA! The sensor has a full sensing range of /-3g The burst echo to return to the sensor. By measuring the echo pulse width, the distance to target can easily be calculated.
Features of ADXL335:
3-axis sensing.Small, low profile package.4 mm × 4 mm × 1.45 mm LFCSP.Low power : 350 μA (typical).Single-supply operation: 1.8 V to 3.6 V.10,000 g shock survival.Excellent temperature stability.BW adjustment with a single capacitor per axis.RoHS/WEEE lead-free compliant.
Product Specification
Part Number | AB030 49E |
Application | Industrial, Sensing & Instrumentation, Medical |
Operating Supply Voltage | 2.3V ~ 5.3V |
Pin Count | 3 Pin |
Operating Temperature | -40 to 90 Deg C |
Current Consumption at Rest | 3mA |
Current Consumption when Switched | 8 mA |
Mounting holes size | 2 mm |
Product Description
Features:
- Analog magnetic sensor module and a digital interface
- Built-in 13 LED build a simple circuit to produce a magnetic flash
- Black PCB board, made of the flame retardant epoxy resin material
- Small size and high sensitivity.
- Fast response temperature and good performance.
- Motor speed measurement
- Object position detection
- Smart car
- Electronic bricks
- VCC ↔ 2.3V ~ 5.3V
- GND ↔ power supply ground
- AOUT ↔ MCU.IO (analog output)
- DOUT ↔ MCU.IO (digital output)