Search
Search Criteria
Products meeting the search criteria
Weigand AR031 SD Card Module Slot Socket Reader
SD Card Reading Writing Module for Arduino with the on-board 3.3V regulator. This SD Card module can make your SD application easier and simple. Through programming, you can read and write to the SD card using your Arduino. With the help of this module, can use for SD Card more easily, such as for MP3 Player, MCU/ARM system control. It can be easily interfaced as a peripheral to your Arduino, and other embedded boards and micro-controllers. Through programming, you can read and write to the SD card over the SPI interface.
XH-M131 DC 12V Light Control Switch Photoresistor Relay Module
Buy the new XH-M131 DC 12V Light Control Switch Photoresistor Relay Module. The Light Detection and brightness detection, detection can be adjusted via potentiometer brightness valve point comes relays, and do all kinds of brightness detection switch, you can control all kinds of street lights automatically turn on at night, during the day and automatically turns off and car supplies control and automation equipment.Using the photoresistor induction light intensity comes with the relay and direct control load. It has a Distribution bit sensitivity adjustment. The start relay threshold is set by adjusting the potentiometer. 12 V power input is designed for relay board regulator transistors to provide sensors and is Used to make the product more stable and reliable. It has four fixed bolt hole for easy installation.
DS3231 Real Time Clock (RTC) Module, 32K (DS3231)
This Infrared Obstacle Avoidance Sensor Module is an inexpensive solution to avoidance detection for robotics and other electronics uses. It comes as an assembled module, as shown above, there are only four pins: 5-volts, GND, output, and EN. Output is an active LOW and has an onboard status LED. It’s very easy to interface directly with micro-controllers. It also works with the Raspberry Pi with a voltage range of 3-6 volts. Connect Vcc to 3-volts.
The enable pin “EN” will disable the device when HI (Vcc) and enable when LO (GND). The onboard jumper can be left open to allow external control of enable/disable of the module. There are two potentiometers on the module one controlling operating frequency (centred at 38 kHz) the other controlling intensity. The detector was designed for 38 kHz and the onboard oscillator circuit is based on a 555 timer.
The enable pin “EN” will disable the device when HI (Vcc) and enable when LO (GND). The onboard jumper can be left open to allow external control of enable/disable of the module. There are two potentiometers on the module one controlling operating frequency (centred at 38 kHz) the other controlling intensity. The detector was designed for 38 kHz and the onboard oscillator circuit is based on a 555 timer.
Infrared IR Distance / Proximity Sensor Sharp GP2Y0A02YK0F (GP2Y0A02YK0F)
The Sharp distance sensors are a popular choice for many projects that require accurate distance measurements. This IR sensor is more economical than sonar rangefinders, yet it provides much better performance than other IR alternatives. Interfacing to most microcontrollers is straightforward: the single analog output can be connected to an analog-to-digital converter for taking distance measurements, or the output can be connected to a comparator for threshold detection. The detection range of this version is approximately 20 cm to 150 cm (8″ to 60″).
The GP2Y0A02 uses a 3-pin JST PH connector that works with our 3-pin JST PH cables for Sharp distance sensors (not included); the top picture on the right shows a shorter-range Sharp analog distance sensor with one of these cables. These cables have 3-pin JST connectors on one end and are available with pre-crimped male pins, pre-crimped female pins, and with unterminated wires on the other end.
The GP2Y0A02 uses a 3-pin JST PH connector that works with our 3-pin JST PH cables for Sharp distance sensors (not included); the top picture on the right shows a shorter-range Sharp analog distance sensor with one of these cables. These cables have 3-pin JST connectors on one end and are available with pre-crimped male pins, pre-crimped female pins, and with unterminated wires on the other end.
7 Color Flash Sensor Module For ARDUIN0
This is 7 color flashing LED module 5mm round high-brightness light-emitting diode. The module contains a 7-color 5mm LED with a built-in chip that sequentially flashes each color in turn. The color pattern is repeated in about 15 seconds.
Specification:Product Type: LEDShape: Round LED 5mm DIP typeLens type: white mistStandard Forward Voltage: 2.5-6V Forward Current: 40mA
Specification:Product Type: LEDShape: Round LED 5mm DIP typeLens type: white mistStandard Forward Voltage: 2.5-6V Forward Current: 40mA
Mini PIR Sensor Module (ML020)
This device is a miniature passive Infrared (PIR) motion sensor that features automatic control and a repeatable trigger. Typical applications include security products, industrial automation and control, auto sensing of electrical equipment, lighting, toys, etc.
HC-SR505 Mini Infrared PIR Motion Sensor Precise Infrared Detector Module H
HC-SR505 small body sensing module is based on infrared technology, automatic control products, high sensitivity, high reliability, ultra-small, ultra-low-voltage operation mode. Widely used in various auto-sensing of electrical equipment, especially battery-powered automatic control products.
HC-SR505 Mini Infrared PIR Motion Sensor Precise Infrared Detector Module H
HC-SR505 small body sensing module is based on infrared technology, automatic control products, high sensitivity, high reliability, ultra-small, ultra-low-voltage operation mode. Widely used in various auto-sensing of electrical equipment, especially battery-powered automatic control products.
White TEC1-12706 Thermoelectric Peltier Cooler Module, 12V (TEC1-12706)
hermoelectric coolers (TEC or Peltier) create a temperature differential on each side. One side gets hot and the other side gets cool. Therefore, they can be used to either warm something up or cool something down, depending on which side is used. You can also use temperature differential to generate electricity.
A thermoelectric cooling (TEC) module is a semiconductor-based electronic component that functions as a small heat pump. By applying DC power source to a TEC, heat will be transferred from one side of the module to the other. It creates a cold and hot side. They are widely used in industrial areas, for example, computer CPU, CCDs, portable refrigerators, medical instruments, and so on.
When exposed to different temperatures on both sides it will also work as a generator and generate electricity depending on the temperature difference
ADXL335 - Triple Axis Linear Accelerometer (ADXL335)
ADXL335 is a Breakout board based on 3 axis ADXL335 IC from Analog Devices. The Accelerometer Module require no external devices and works on 5V power supply. It can be directly interfaced to ADC of a microcontroller without any external components.
This module can be used to sense motion or tilt(in case of non moving) in 3 axis.This is the latest in a long, proven line of Analog Sensors- the holy grail of accelerometers. The ADXL335 is a triple axis MEMS accelerometer with extremely low noise and power consumption - only 320uA! The sensor has a full sensing range of /-3g The burst echo to return to the sensor. By measuring the echo pulse width, the distance to target can easily be calculated.
Features of ADXL335:
3-axis sensing.Small, low profile package.4 mm × 4 mm × 1.45 mm LFCSP.Low power : 350 μA (typical).Single-supply operation: 1.8 V to 3.6 V.10,000 g shock survival.Excellent temperature stability.BW adjustment with a single capacitor per axis.RoHS/WEEE lead-free compliant.
| Brand | REES52 |
| Part Number | ADXL335 |
| Accelerometer Type | AC Response |
| Number of Axes | 3 |
| Sensing Axis | XYZ |
| Output Type | Analog |
| Excitation Voltage | 1.8 V to 3.6 V. |
| Operating Temperature Range | -20 to 70 deg C |
ADXL335 is a Breakout board based on 3 axis ADXL335 IC from Analog Devices. The Accelerometer Module require no external devices and works on 5V power supply. It can be directly interfaced to ADC of a microcontroller without any external components.
This module can be used to sense motion or tilt(in case of non moving) in 3 axis.This is the latest in a long, proven line of Analog Sensors- the holy grail of accelerometers. The ADXL335 is a triple axis MEMS accelerometer with extremely low noise and power consumption - only 320uA! The sensor has a full sensing range of /-3g The burst echo to return to the sensor. By measuring the echo pulse width, the distance to target can easily be calculated.
Features of ADXL335:
3-axis sensing.Small, low profile package.4 mm × 4 mm × 1.45 mm LFCSP.Low power : 350 μA (typical).Single-supply operation: 1.8 V to 3.6 V.10,000 g shock survival.Excellent temperature stability.BW adjustment with a single capacitor per axis.RoHS/WEEE lead-free compliant.
49E Linear Hall Effect Sensor Module (AB030 49E)
Product Specification
| Part Number | AB030 49E |
| Application | Industrial, Sensing & Instrumentation, Medical |
| Operating Supply Voltage | 2.3V ~ 5.3V |
| Pin Count | 3 Pin |
| Operating Temperature | -40 to 90 Deg C |
| Current Consumption at Rest | 3mA |
| Current Consumption when Switched | 8 mA |
| Mounting holes size | 2 mm |
Product Description
Hall Switch Integrated Circuit Using hall Effect Principle. USES The Semiconductor Integrated Technology Manufacturing Magnetic Susceptibility of the Circuit. Its Input For the Magnetic Induction Intensity, the Output is a Digital Voltage Signal.
Features:
Features:
- Analog magnetic sensor module and a digital interface
- Built-in 13 LED build a simple circuit to produce a magnetic flash
- Black PCB board, made of the flame retardant epoxy resin material
- Small size and high sensitivity.
- Fast response temperature and good performance.
- Motor speed measurement
- Object position detection
- Smart car
- Electronic bricks
- VCC ↔ 2.3V ~ 5.3V
- GND ↔ power supply ground
- AOUT ↔ MCU.IO (analog output)
- DOUT ↔ MCU.IO (digital output)