Search

Features:

• Easy to use
• Easy to Soldered
• Affordable cost
• Good Quality PCB
• Comes with all the components

Package Includes:

1 x Electronic Acoustic Clap Control Switch DIY Kit Sound Sensor Electronic Circuit DIY Suit Integrated PCB Module

Product Description :

This L9110 Fan Module Fire Fighting Robot for Arduino controls the rotation direction of the motor, hence the fan. Designed with the mounting hole, compatible with servo motor control.

The module bows out the flame of light in the 20cm distance. It is an essential part of firefighting robot development.

It equips quality and high-efficiency propeller.

Connections

1. VCC ↔ 5V,
2. GND ↔ GND,
3. INA ↔ 9,
4. INB ↔ 8,

Package Includes:

1 x L9110 Fan Module

1 x Propeller set

This 1-channel 5V control Single-Pole Double-Throw (SPDT) High-level trigger AC power relay board can be controlled directly via a microcontroller and switch up to 10A at 250 VAC. The inputs of 1 Channel 5V Relay Module are isolated to protect any delicate control circuitry.

The default state of the relay when the power is off for COM (Power) to be connected to NC (Normally Closed). This is the equivalent of setting the relay board IN pin to HIGH (has 5V sent to it).

A wide range of microcontrollers such as Arduino, AVR, PIC, ARM, etc can be used to control this 5V relay module

NOTE : There Is Printing Mistake On  Module 250VAC To 30VAC And 125VAC to 28VAC But Working Will Be Same.

Pin Configuration:

Connection Diagram:

This 1 channel 5V 10A relay control board module with optocoupler modules is compliant with international safety standards, control and load areas isolation trenches it has a single relay a genuine.

The inputs of 5V 1-Channel Relay 10A Relay Module are isolated to protect any delicate control circuitry.

The power supply and relay instructions, lit, a disconnect are off. The input signal, signal, common Terminal and start conducting. It can be used as a single chip module for appliance control and work with both DC or AC signals where you can control the 220V AC load.

A wide range of microcontrollers such as Arduino, AVR, PIC, ARM and so on can control 1 channel 5V 10A Relay Control Board Module with Optocoupler.

Note: On the high level and low level-triggered mode, friends who do not understand, have a look

• High-level trigger refers to the signal voltage between input and trigger, can be understood as a signal input with VCC cathode short-circuit triggered a way;
• Low-level trigger refers to the signal voltage between the input terminal and Earth OV trigger, can be understood as a signal input terminal and the GND negative electrode short circuit triggered is a way  1-channel relay module connection.

This is a 2 Channel isolated 5V 10A relay module Optocoupler for Arduino PIC ARM. It can be used to control various appliances and other types of equipment with a large current. It can be controlled directly with 3.3V or 5V logic signals from a microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic).

This relay has a 1×4 (2.54mm pitch) pin header for connecting power (5V and 0V), and for controlling the 2 relays.

The pins are marked on the PCB as:

• GND – Connect 0V to this pin.
• IN1 – Controls relay 1, active Low Relay will turn on when this input goes below about 2.0V
• IN2 – Controls relay 2, active Low Relay will turn on when this input goes below about 2.0V
• VCC – Connect 5V to this pin. Is used to power the optocouplers

Note: This 5V Dual Channel Relay Module is for low level trigger only. 

About high level and low level-triggered mode:

1. High-level trigger refers to the signal voltage between input and trigger, can be understood as a signal input with VCC cathode short-circuit triggered a way;
2. Low-level trigger refers to the signal voltage between the input terminal and Earth OV trigger, can be understood as the signal input terminal and the GND negative electrode short circuit triggered away  1-channel relay module connection

Jumper Instruction = The relay can be turned on when we connect 5v to one end and the other to -5v / Gnd, while talking about the jumper, if we short the VCC and the middle pin, then our relay will act as high level-triggered relay means that when we will apply 5V input on its input pin it will be turned on and when the jumper will be set to “middle and GND”, it will act as a low-level triggered relay, It means that relay will be triggered when we implement the 5V / GND on its input pin.

This is a 2 Channel 5V Relay module, be able to control various appliances, and other equipment with large current. It can be controlled directly by Microcontroller (8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic).5V 2-Channel Relay interface board and each one needs 15-20mA Driver Current Equipped with high-current relay, AC250V 10A; DC30V 10A Standard interface that can be controlled directly by microcontroller (8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic) Indication LED’s for Relay output status.

Add the desired memory to your Arduino project to store the data, Media etc. Micro SD Card Reader Module also called Micro SD Adaptor which is designed for dual I/O voltages. The Module is a simple solution for transferring data to and from a standard SD card. The pinout is directly compatible with Not only with Arduino as shown in the diagram in below, but can also be used with other microcontrollers. Micro SD Card Reader Module has an SPI interface which is compatible with any sd card and it uses 5V or 3.3V power supply which is compatible with Arduino UNO/Mega.SD module has various applications such as data logger, audio, video, graphics.

There are total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground, VCC is the power supply, MISO, MOSI, SCK is the SPI bus, CS is the chip select signal pin; 3.3V regulator circuit: LDO regulator output 3.3V as level converter chip, Micro SD card supply.

With this Module, general AVR microcontroller system can read the signal

Note: Product image may vary in terms of design, Color of PCB from actual product.

Interfacing with Arduino Uno:

Note:

ACS712 is based on the Hall detection principle, please try to avoid the magnetic field, when using it as it may impact the reading accuracy.

Connection Diagram:

Module with antenna, mini size with strong signal. EEPROM save the configuration parameter data when power down. With data backup battery. With LED signal lights. Compatible with various flight control modules. Specification: Model: GY-GPS6MV2. With ceramic antenna. With LED signal indicator lamp. Power supply: 3-5V. The default baud rate: 9600. Compatible with different flight controller module. Size: Approx. 2.5cm x 3.5cm /0.98 x 1.38inch

This is RF Transmitter Receiver Module 315MHz Wireless Link Kit For Arduino.

This wireless transmitter and receiver pair operates at 315Mhz. They can easily fit into a breadboard and work well with microcontrollers to create a very simple wireleReceiving frequency (MHz)ss data link. Since these are only transmitters, they will only work communicating data one-way, you would need two pairs (of different frequencies) to act as a transmitter/receiver pair.

This Radio Transmitter & Receiver pair is perfectly matched to allow you to control items from a distance up to 500 feet wirelessly! Connect the transmitter to your Arduino, Raspberry Pi or other microcontroller and the receiver to whatever you’d like to control.

Both the transmitter and receiver are in tune to the same Radio Frequency so that when the transmitter emits a signal, the receiver will hear it wirelessly. Great for easy and simple wireless control! Arduino & Raspberry Pi 2 / B / B / A Compatible!

SIM800L V2 5V Wireless GSM GPRS MODULE power supply for 5 v, computer debug USB to TTL serial port. Power to the output current of 800 ma, TTL serial interface is compatible with 3.3 V and 5 V micro-controller, can be directly after purchase and single-chip computer connection.

The IPX antenna, the antenna interface can be arbitrary switching PCB glue stick antenna and suction cups. SIM800L 4 frequency communications, data available in the world. Do foreign trade and foreign trade projects preferred.

SIM800L V2.0 GSM/GPRS Module is a QUAD-BAND GSM/GPRS module which compatible with Arduino. The module works to add both of GSM features (voice call or SMS) and GPRS features. The advantages of these modules are the VCC and TTL serial levels that have 5V voltage, so you can directly connect it to Arduino or another minimum system with 5V of the voltage level.

There are so many GPRS/GSM modules on the market which need to add 5V regulator and level converter circuit, while SIM800L V.2 GSM/GPRS module already has a built-in regulator circuit and TTL level converter on the board.

Pin Description

5v: Power interface Power the module CONNECT TO DC 5v
GND: Connect to GND.
VDD: TTL UART interface The TTL UART serial interface, you can connect the MCU like 51MCU or ARM or MSP430 directly. The pin of VDD is used to match the voltage of the TTL.
SIM_TXD: SIM module Transmitter.
SIM_RXD: SIM module Receiver.
GND: If this pin is unused, keep open.
RST: RST the module, if this pin is unused, keep open. 

This is Small SIM800L GPRS GSM Module Micro SIM Card Core Board Quad-band TTL Serial Port with the antenna, in this module two antennas have been included.

SIM800L GSM/GPRS module is a miniature GSM modem, which can be integrated into a great number of IoT projects. You can use this module to accomplish almost anything a normal cell phone can; SMS text messages, make or receive phone calls, connecting to the internet through GPRS, TCP/IP, and more! To top it off, the module supports quad-band GSM/GPRS network, meaning it works pretty much anywhere in the world

First is made of wire (which solders directly to NET pin on PCB) – very useful in narrow places. Second – PCB antenna – with double-sided tape and attached pigtail cable with IPX connector. This one has better performance and allows to put your module inside a metal case – as long the antenna is outside.

Caution: Use a resistor divider circuit before interfacing it with Arduino to avoid the damage to the module.

The ESP32 LoRa SX1278 0.96 Inch Blue OLED Display BT WiFi Module for Arduino, this series is the new development of the cost-effective networking program.

The main chip using Lexin ESP32, Tensilica LX6 dual-core processor, clocked at 240MHz, computing power up to 600DMIPS, chip built-in 520 KB SRAM, 802.11 b / g / N HT40 Wi-Fi transceiver, baseband, protocol stack, and LWIP, integrated dual-mode Bluetooth (traditional Bluetooth and BLE low power Bluetooth).

Bluetooth MP3 Decoding Board Module with SD Card Slot / USB / FM / Remote Decoding Board Module is compact size Music player which can be installed anywhere like in your vehicle, on Home Theater Speakers system. If you have an old conventional Music system without USB/AUX/Bluetooth Support, then this device will be the right choice to add these all feature in your music system. It can also be used to build your own music system.

All You need is an amplifier board & speaker to use this module. The module comes with Bluetooth FM USB and mp3 audio board with LCD display with IR remote control. The player has Multiple sources of input i.e. AUX, Bluetooth, USB, SD card along with FM radio.

The LCD display shows the information of Track number, Selected Input Source, and Selected FM Frequency.

Precautions:

1. This kit is not for the electronics hobbyist. Proper knowledge about the subject is required to understand and make the complete project. We do not hold any responsibility for any issues or help either due to negligence, ignorance or lack of proper knowledge about the subject.
2. This unit is used to feed an amplifier, from the amplifier you can drive the speaker. Do not connect speakers directly to this unit.

Features :

• Comes with IR Remote Control
• Stereo Digital Audio Output
• Can be used as an audio receiver
• Support USB/TF Card Slot/Bluetooth/FM/AUX switching, also supports folder selection and playback
• Stereo Bluetooth with a call can also receive hands-free calls
• DIY speakers and modified audio/car rare weapon
• Support MP3/WMA/WAV/FLAC/APE format music
• Can be used to play songs from USB, SD card, Bluetooth, and FM radio